Rubberized Plastic Cement Français
Description
This excellent wet or dry surface rubberized plastic cement CR-320 contains elastomers and specially selected fibers for multipurpose applications. It is formulated to offer resistance against bad weather and flexibility as well as to be easy to apply. It becomes a strong, waterproof flexible coating once dried. Ideally suited for flat or metal roofs, but not recommended for asphalt shingles.
Surface Preparation
Surface must be structurally sound, clean and free of dust, dirt, rust, oil, grease, chipped paint, frost or any other contaminants.
Application
Can be applied with a towel, a caulking gun, a putty knife or by hand with gloves. To fill joints and cracks, push profoundly into gaps making bulge out on surface to avoid accumulation of water. Repair cracks, holes by applying a coat of 3 mm (1/8'') thick on defective sections and overtake of 150 mm (6'') around repairs. To ease application in cold season, keep product in a warm place.
Cleanning
Clean tools and equipment with mineral spirits.
Norm
CAN/O.N.G.C. 37.29-M89
Package
Available in tube of 300 ml and pails of 4 kg and 20 kg.
Shelf Life
This product can be conserved in its original container, tightly sealed, up to 12 months after purchasing date by the applicator.
Technical Data Table
Specifications  
Color Black
Solids by Volume 70 to 80 %
Weight 1,05 kg/L (8,75 pounds/gal)
Coverage 0,3 m²/kg (16 ft²/gal) coat of 3 mm (1/8'')
Tube : bead of 3 mm (1/8'') couvers ± 25 feet
Dry Time*

To 50 % R.H. 20° C (68° F)

To the Touch* 1 hour
Completely Dry* 24 hours
Service Temperature Maximum : 85° C (185° F) dry coating
Application Temperature Ambient (Thickens at low temperature)
Chemical Resistance

Resistant to water calcium chloride, salt and to lightly acid or alkaline solutions. Do not resist to oils, greases and solvents.

Permeance to Water Vapor (ASTM E96) 3 mm (1/8'') coat before drying 2.9 ng/Pa.m2.s (0.05 perms)
 

* Drying Time depend  of surface porosity and temperature.

Restriction
If product is applied near a ventillation unit or an air conditioner, take necessary precautions to avoid infiltration solvent odor inside. Protect freshly applied product and open container from open flame and adjacent welding activity. Do not apply all at once on vertical joints of more than 25 mm (1'') in width. Solvent contained in the product may stain wood and other absorbent materials. For EXTERIOR USE only.
Warranty
10 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under no circumstances will the manufacturer be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer's control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).

Rubberized Plastic Cement
Rubberized Plastic Cement
Sans Amiante
Avertissement Simdut Simdut

CONTENTS MAY CATCH FIRE: Contains petroleum distillates. May cause dizziness, headache or nausea. May cause nose, throat, eyes and skin irritation. Keep away from heat sources, sparks and flames. Do not smoke. Use only with adequate ventilation. Do not breathe vapors. Wear safety glasses and appropriate gloves. KEEP OUT OF REACH OF CHILDREN.


FIRST AID TREATEMENT: Eyes : In case of contact, flush immediately with plenty of water for at least 15 minutes and get medical attention immediately; for skin, wash thoroughly with soap and water. If you experience difficulties in breathing, leave the area to obtain fresh air. If difficulties continues, get medical assistance immediately. If swallowed, do not induce vomiting. Get medical attention immediately.
 
PDFdownload PDF version