Elastomeric Roof Coating White Français
Description
SEALFLEX White elastomeric roof coating CR-4316 is a 100% acrylic water-based emulsion specially formulated to cover and repair caravan and recreative vehicules roofs, but also steel, wood, concrete, shingles and composite roofs, U.V resistant and long-lasting. This waterproofing membrane reflects sun rays and resists to mildew, discoloration, cracking, peeling-off and chalking.
Surface Preparation
It is very important to clean all surfaces with a universal degreaser. To brush and rinse with plenty of water. Surfaces must be sound, clean and free from rust, loose paint, dust, dirt, grease and mildew. Clean with high pressure water. Scarify glossy areas. Holes and cracks can be repaired with Condor elastomeric plastic cement. Allow repairs to dry for 24 hours prior to apply SEALFLEX elastomeric coating.
Application
Do not begin outside work if temperature is unsure for the next 48 hours. Test on a small area to determine suitability of material. Being water-based, avoid application under full sun and protect surface against rain until completely dry. Do not apply over bituminous roofs. Do not dilute. Stir well before use. Temperature and relative humidity are critical factors for an adequate drying. For application and curing of Sealflex we need a temperature more than 10ºC and a relative humidity less than 85%. Therefore, ideal conditions are 25°C and 50% of relative humidity. Make sure roofs have slope to shed water. It is recommended to apply 2 to 3 coats to achieve a dry 0.76 mm (30mil or 1/32’’) thickness.
Package
Available in 3,78 L and 18.9 L pails.
Storage
KEEP FROM FREEZING.
Shelf Life
This product can be stored 1 year after purchasing date when kept in its tightly closed original container.
Technical Data Table

Conform to ASTM 6083 norm.

  CR-4316
Color White
Solid content 66 to 68 %
Density, shore A (ASTM D2240) 1,4 kg/L (about) (14 pmd/gal)
PH 8.5 to 9.5
Hardness, shore A (ASTM D2240) 40 for 21 days
Strength at rupture (ASTM D412) 350 PSI (2,41 MPA)
Tear Strength (ASTM D624) 49 PPI
Adhesion-in-Peel (ASTM C794) 40 PPI
Tensile Adhesion (ASTM C1135)  
25 % 75 PSI (0,52 MPA)
50 % 110 PSI (0,76 MPA)
100 % 140 PSI (0,97 MPS)
Adhesion to Rigid Substrates (ASTM D429) 1015,26 PSI (7 MPA)
Fragility at 40°C without rupture
V.O.C. content 250 g/L
Permeance to water (ASTM E96) Permeable
 

* Drying time depends on application method, temperature and porosity surfaces

Warranty
10 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under no circumstances will the manufacturer be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer's control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).

Elastomeric Roof Coating
Elastomeric Roof Coating
Ecologic
Warning Simdut

MAY IRRITATE EYES AND SKIN. Do not get in eyes, on skin or on clothing. Keep out of reach of children.


FIRST AID TREATMENT: Contains Stoddard solvent. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, clean with mineral oil followed by soapy water then rinse well.
 
PDFdownload PDF version