Sealflex Roof Siliconized Coating Green Français
Description
SEALFLEX™ ROOF is a 100% acrylic water-based emulsion specially formulated to cover flat (no tar) and shingle roofs. This waterproofing membrane reflects sun rays, resists U.V rays and is long-lasting. It resists to mildew, discoloration, cracking, peeling-off and chalking. Ideal for all surfaces but no metal ones.
Surface Preparation
Surfaces must be sound, clean and free from dust, dirt and mildew. Holes and cracks can be repaired with Sealflex™ Colored Plastic Cement, allowing a 24 hours drying.
Application
Avoid application under full sun or over hot surfaces. Not recommended on metal surface. Do not dilute. Stir well before use and close container between uses. For application and curing of Sealflex Roof, it needs a temperature higher than 10ºC. Protect surface against rain untilitis completely cured. Make sure roofs have slope to shed water. We recommend 2 to 3 coats to achieve a dry 0.76 mm (30 mils or 1/32’’) thickness. SEALFLEX™ Roof can be applied with a paintbrush, a roller or an industrial sprayer. Always spread the coating in the same direction. Apply the second coat at right angle of the first one, allowing few hours to dry.
Cleanning
Clean tools with water while product is still fresh.
Package
Available in 3,78 L and 17 L pails.
Storage
Keep from freezing. Store at temperatures between 10ºC and 30ºC.
Shelf Life
This product can be stored 1 year after purchasing date when kept in its tightly closed original container.
Technical Data Table

Conform to ASTM 6083 norm.

  CR-4331
Color Green
Solid content 66 to 68 %
Density, shore A (ASTM D2240) 1,4 kg/L (about) (14 pmd/gal)
PH 8.5 to 9.5
Hardness, shore A (ASTM D2240) 40 for 21 days
Strength at rupture (ASTM D412) 350 PSI (2,41 MPA)
Tear Strength (ASTM D624) 49 PPI
Adhesion-in-Peel (ASTM C794) 40 PPI
Tensile Adhesion (ASTM C1135)  
25 % 75 PSI (0,52 MPA)
50 % 110 PSI (0,76 MPA)
100 % 140 PSI (0,97 MPS)
Adhesion to Rigid Substrates (ASTM D429) 1015,26 PSI (7 MPA)
Fragility at 40°C without rupture
V.O.C. content 250 g/L
Permeance to water (ASTM E96) Permeable
 

* Drying time depends on application method, temperature and porosity surfaces

Note
Do not begin outside works if temperature is unsure for the next 48 hours. Make sure that work is done in a safe manner.
Warranty
5 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under no circumstances will the manufacturer be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer's control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).

Sealflex Roof Siliconized Coating
Sealflex Roof Siliconized Coating
Ecologic
Warning Simdut

MAY IRRITATE EYES AND SKIN. Do not get in eyes, on skin or on clothing. Keep out of reach of children.


FIRST AID TREATMENT: Contains Stoddard solvent. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, clean with mineral oil followed by soapy water then rinse well.
 
PDFdownload PDF version