Fibered Aluminum Roof Coating Français
This CR-90 fibered aluminum asphalt coating is asbestos free with special resins. Once dried, it gives a reflective, glossy and durable finish and reduces temperature absorption and delays supports contraction and dilatation. This asphalt based paint gives, once dry, a reflective, glossy and durable finish. Excellent protector against UV and oxidation for roofs, flashings, metal structures etc. You can also use on any other stable bituminous coating as CR-300, CR-340, coal tar coatings,flashing or on metal surfaces which have a very dry primer or paint.
Surface Preparation
Avoid use if showers are foreseen. Surfaces must be structurally sound, clean, dry and free of dust, dirt, rust, oil, grease, flakes and other contaminants. Old paints or coatings must be strongly adhered. Previously, fill holes, cracks and weak spots with an appropriate Condor plastic cement.
Do not apply if showers are foreseen or if there is a possibility of dew point before it is completely dry because humidity can tarnish freshly applied coating. Stir product well before use. To ease application in cold season, keep product in a warm place. Apply with a squeegee, a brush, a roller or a paintbrush. Avoid over-brushing. First, apply a coat on overlaps and nail, than, apply a coat uniformly all over the surface. Direct application of product over felt coatings may affect its coating and result in sag of the felt on slope surfaces
Clean tools and equipment with mineral spirits.
CAN/O.N.G.C. 37.42-M89 type II
Available in 3.78 L and 18.9 L format.
Shelf Life
This product can be conserved in its original container, tightly sealed, up to 12 months after purchasing date by the applicator.
Technical Data Table
Color Aluminum
Solids by Volume 60 to 70 %
Weight 1,0 kg/L (8,3 pounds/gal)
Coverage 1,0 to 2,25 L/m² (2 to 4,5 gal/100 ft²)
Dry Time*

To 50 % R.H. 20°C (68°F)

To the Touch* 4 to 8 hours
Completely Dry* 48 hours
Service Temperature -30°C to 80°C (-22°F to 176°F)
Application Temperature Can be applied at low temperature but preferably above 10°C (50°F).
Chemical Resistance

Resistant to water calcium chloride, salt and to lightly acid or alkaline solutions. Do not resist to oils, greases and solvents.

Permeance to Water Vapor (ASTM E96) 3 mm (1/8'') coat before drying 2.9 ng/Pa.m2.s (0.05 perms)

* Drying Time depend of surface porosity and temperature.

Avoid contact with polystyrene insulation foam or any solvent alterable materials. If applied near a ventillation unit or an air conditioner, take necessary precautions to avoid infiltration solvent odor inside. It is not recommended on bare wood or on porous surfaces. Make sure that bituminous surfaces or coal tar coatings are stable, completely dry and free of volatile residues. This paint may crack on smooth multi-coats asphalt roof coverings due to the instability of bitumen. This product may change color in aluminum oxidizing environments. Do not apply on wet surfaces. Protect freshly applied product and open container from open flame and adjacent welding activity. For EXTERIOR USE only.
5 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under no circumstances will the manufacturer be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer's control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).

Fibered Aluminum Roof Coating
Fibered Aluminum Roof Coating
Sans Amiante

Flammable liquid and vapour. May be fatal if swallowed and enters airways. Suspected of causing cancer. Causes damage to organs through prolonged or repeated exposure.

Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not breathe dust/fumes/gas/mist/vapours/spray. Wash exposed and/or contaminated area thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves/protective clothing/eye protection/face protection.

IF SWALLOWED: Do NOT induce vomiting. Immediately call a POISON CENTER or a doctor If exposed: Call a POISON CENTER or doctor/physician. Get medical advice/attention if you fell unwell. In case of fire: Use water fog, foam, dry chemical or carbon dioxide. Do not use straight of water. Store in a well ventilated place. Keep cool. Store locked up. Dispose of contents / container by a local waste disposal company according to regional regulations.

PDFdownload PDF version