Eagle Bond Universal Thin-Set Mortar Français
EAGLE BOND is an high quality thin-set mortar that only needs water to install all types of natural stones and tiles on inside concrete surfaces. This thin-set is formulated for ceramic tiles, vitrified or not, either on horizontal or vertical surfaces. Excellent for residential and light commercial applications. Mixed with its polymer EAGLE BOND PLUS, it will give the highest results in the industry for interior or exterior installations of natural stone, glass, porcelain and ceramic tiles, etc. EAGLE BOND gives an excellent adhesion on more demanding jobs. Take note that rigorous attention must be taken to execute surface preparation conform to trade practices and Eagle Black’s surface preparation guidelines.
Surface Preparation
All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease, paint, curing agent, coatings and loose particles. They must also be exempt from any trace of acids, alkalis or any other material that can reduce adhesion. When Eagle Bond is mixed with Eagle Bond Plus, the only recommended wood substrate for residential floors is exterior grade plywood installed in an interior dry area. All concrete substrates shall be completely cured and at least 28 days old, free from hydrostatic conditions and/or extreme humidity problems. Remove completely all traces of paint, coating, loosely bonded toppings. Ambient surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during the installation and for the first 24 hours.
Spread and scratch mortar with flat edge of trowel. Quickly add mortar and use notched side , spread mortar uniformly, taking care to trace ridge lines in the same straight line direction. Prepare only the quantity that can be apply in less than 15 minutes. If ridges have slightly dried and there is skin formation at the surface, there will be no adherence, mortar will have to be removed and a fresh coat applied. Press tiles firmly with a back and forth motion across ridges to obtain full mortar transfer at the back of tiles at 1/3 of their thickness in mortar. Never wet tiles prior to their application, if so, it must be advised by tile manufacturer.
In a clean container, pour exactly 330 ml of Eagle Bond Plus or 260 ml of fresh and clean water per kg of Eagle Bond by adding gradually the powder while mixing with a low-speed drill and mixer. Blend for 1 to 2 minutes scraping recipient walls and paddle to obtain a homogeneous trowelable consistency. Let mortar sit for 10 minutes, than remix without adding any more water or powder. Apply immediately. Occasionally remix while using it, with no water addition.

Approximate coverage for a 22.7 kg (50lb) bag : Truelle de 6 X 6 X 6 mm (¼” X ¼” X ¼”) : …………..8,4 m² (90 ft²) Truelle de 6 X 10 X 6 mm (¼” X 3/8” X ¼”) : ………..6,5 m² (70 ft²)

Protect surfaces for 48 hours. Curing time may vary according to temperature and humidity level. Make sure application is dry prior to allow light traffic for grouting.
Clean working tools and hands with water while product is still fresh.
Available in 11,34 kg and 22.7 kg bags. Grey or white color.
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
CARACTERISTICS CURE Eagle Bond (26% water)
Pot life   15 minutes
Open time   15 minutes
Set time final ASTM C-191   < 17 hours
Shear Strenth ANSI A118.1    
Wall Tiles 28 days 2,24 Mpa (325 Psi)
Mosaics 28 days 2,66 Mps (386 Psi)
Quarrys 28 days 2,63 Mpa (381 Psi)
Quarrys / Plywood 28 days N/A

* Drying Time depend of surface porosity and temperature.

The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Bond
Eagle Bond
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.

FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
PDFdownload PDF version