Eagle Bond Plus High Performance Additive Français
EAGLE BOND PLUS is an high quality acrylic latex, specially formulated to be used with EAGLE BOND thin-set mortar. Together, they give higher performance in flexibility and adhesion for interior or exterior installations of ceramic tiles, vitrified or not, either horizontally or vertically. It is excellent for residential or commercial uses. There combination give highest performance of the industry for natural stone, porcelain, glass, ceramic tiles, etc. and are the only system recommended for water submerged ceramic tile applications like pools or fountains. Even more than conventional substrates, EAGLE BOND/EAGLE BOND PLUS provides excellent adhesion over asbestos or composite vinyl tiles, existing ceramic surfaces, cementitious terrazzo, cut-back residues, etc. Take note that rigorous attention must be taken to execute surface preparation conform to trade practices and Eagle Black’s surface preparation guidelines.
Surface Preparation
All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease, paint, curing agent, coatings and loose particles or any trace of acids, alkalis or any other material that can reduce adhesion. The only recommended wood substrate for residential floors is an exterior grade plywood installed in an interior dry area. All concrete substrates shall be completely cured and at least 28 days old, free from hydrostatic conditions and/or extreme humidity problems. They must be roughened to remove completely all traces of paint, coating, loosely bonded toppings. Ambient, surface and product temperature must be superior than 10ºC (50ºF)and lower than 35ºC (95ºF) before the installation and for the first 24 hours.
In a clean container, pour 330 ml Eagle Bond Plus per kg of Eagle Bond. Add gradually powder while mixing with a low-speed drill and mixer. Blend for 1 to 2 minutes scraping recipient walls and paddle to obtain a homogeneous trowelable consistency. Let mortar sit for 10 minutes, than remix without adding any more water or powder. Apply immediately. Occasionally remix while using it, with no water addition.

Approximate coverage for a EAGLE BOND 22.7 kg (50lb) bag :
Trowel 6 X 6 X 6 mm (¼” X ¼” X ¼”) : 8.4 m² (90 ft²)
Trowel 6 X 10 X 6 mm (¼” X 3/8” X ¼”) : 6.0 m² (70 ft²)

Protect surfaces for 48 hours. Curing time may vary according to temperature and humidity level. Make sure application is dry prior to allow light traffic for grouting.
Clean working tools and hands with water while product is still fresh.
Available in 7,5 L and 18,9L pail.
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container. Keep from freezing.
Shelf Life
Keep from freezing.
Technical Data Table
CARACTERISTICS CURE Eagle Bond with 33% of Eagle Bond Plus
Pot life   > 1 hour
Open time   15 minutes
Set time final ASTM C-191   < 17 hours
Shear Strenth ANSI A118.1    
Wall Tiles 28 days 3,86 Mpa (560 Psi)
Mosaics 28 days 4,59 Mpa (666 Psi)
Quarrys 28 days 5,24 Mpa (760 Psi)
Quarrys / Plywood 28 days 1,89 Mpa (274 Psi)

* Drying Time depend of surface porosity and temperature.

The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Bond Plus
Eagle Bond Plus
Warning Simdut

MAY IRRITATE EYES AND SKIN. Do not get in eyes, on skin or on clothing. Keep out of reach of children.

FIRST AID TREATMENT: Contains Stoddard solvent. If swallowed, call a Poison Control Centre or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, clean with mineral oil followed by soapy water then rinse well.
PDFdownload PDF version