Eagle Crete Normal Set Repair Mortar Français
Description
Eagle Crete is a polymer modified one component cementitious mortar for repairs of old concrete imperfections at many thicknesses. This mortar is specially formulated to recondition old concrete, horizontally as well as vertically with thicknesses that can vary from 6 mm (1/4”) to 75 mm (3”) in one application. It can be used inside or outside.
Surface Preparation
All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease, paint, curing agent, coatings and loose particles. They must also be exempt from any trace or presence of acids, alkalis or any other material that can reduce adhesion. All concrete substrates shall be completely cured and at least 28 days old. They must be roughened for a good adhesion and to remove completely all traces of paint, coating, loosely bonded toppings. Use of Eagle Prime Plus as primer is a good alternative to concrete water saturation or you'll have to saturate concrete surface with clean water within few hours before repairs leaving no excess water. Apply mortar when surface is dry again. Ambient surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during the installation and for the first 24 hours.
Mixing
In a clean container, pour 150 ml of fresh clean water per kg of product and gradually add Eagle Crete powder while mixing with a low-speed drill and a mixer. Blend for 2 to 3 minutes scraping recipient walls and paddle to obtain a homogeneous trowelable lump-free consistency. Slake for 5 minutes and mix again for 1 minute. Proceed with application and finishing.
Curing
Eagle Crete takes 2 to 4 hours to dry. Curing time may vary according to temperature and humidity level. Protect surface from rain, sun and wind. Protecting job against weather, with a plastic in example, must be done without any contact with the surface. That could alter the finish. Wait 16 to 24 hours prior to allow light traffic.
Cleanning
Clean working tools and hands with water while product is still fresh.
Package
This product is available in 5 kg and 15 kg pail
Shelf Life
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
CARACTERISTICS CURE EAGLE CRETE (15% Water)
Pot life   > 1 :00 hour
Set time initial / final ASTM C-191   2:00 hours / 4:00 hours
Density ASTM C-185   2.04 kg/L
Compressive strength ASTM C-109 24 hours
7 days
28 days
17.0 MPa (2466 PSI)
44.0 MPa (6382 PSI)
48.0 MPa (6962 PSI)
Flexural strength ASTM C-348 24 hours
7 days
28 days
7.5 MPa (1088 PSI)
11.5 MPa (1668 PSI)
15.5 MPa (2248 PSI)
Pull-out strength on concrete CSA A23.2-6B 7 days
28 days
1.86 MPa (270 PSI)
1.92 MPa (278 PSI)
Coverage per kg of product   0.05 m² (0.5 ft²) for 12 mm (1/2”) thickness
 

* Drying  Time depend of surface porosity and temperature.

Restriction
Avoid working under intense sun.
Warranty
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Crete
Eagle Crete
Ecologic
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.


FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
 
PDFdownload PDF version