Eagle Econo Plan Self-Leveling Underlayment Compound Français
EAGLE ECONOPLAN is a semi-rapid, polymer modified, cementitious self-leveling mortar that allows smoothing and leveling of interior concrete floors rapidly with less work. This mortar can be used as an underlayment at thicknesses varying from 2 mm to 25 mm (1/8” to 1”). This compound allows smooth surfaces for installation of carpet, ceramic tiles, natural stone, hardwood, vinyl tiles and resilient floor covering.
Surface Preparation
All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease, paint, curing agent, coatings or loose particles, trace of acids, alkalis or any other material that can reduce adhesion. All concrete substrates shall be completely cured and at least 28 days old. It must be roughened for more adhesion and to remove completely all traces of paint, coating, loosely bonded toppings. Use of Eagle Prime Plus as primer is a good alternative to concrete water saturation otherwise saturate concrete surface with clean water within few hours before repairs leaving no excess water. Apply mortar when surface is dry again. Ambient surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during the installation and for the first 24 hours.
In a clean container, pour exactly 5.68 litres of fresh clean water and gradually add 22.7 kg of Eagle Econoplan powder while mixing with a low-speed drill and a mixer. Blend for 2 to 3 minutes scraping recipient walls and paddle to obtain a homogeneous malleable and lump-free consistency is achieved. Slake for 5 minutes and mix again for 1 minute. Apply immediately.
To avoid micro-cracking, protect application from any direct ventilation or heat radiation sources, such as direct sunlight during and after application for a minimum of 24 hours. Eagle Plan takes 2 to 3 hours to set, depending on consistency and ambient conditions. Curing time may vary according to temperature and humidity level. Wait 24 hours before light traffic.
Clean working tools and hands with water while product is still fresh
This product is available in 22.7 kg bag.
Shelf Life
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
Working time   30 minutes
Set time initial / final ASTM C-191   1 :00 hour / 2 :30 hours
Time allowed before installing floor covering or coating   16 to 24 hours selon ºT & H.R.
Self-leveling capacity   15 minutes
Density ASTM C-185   2.02 kg/L
Compressive strength ASTM C-109 24 hours
7 days
28 days
11 MPa (1595 PSI)
20 MPa (2900 PSI)
22 MPa (3190 PSI)
Flexural strength ASTM C-348 24 hours
7 days
28 days
6 MPa (870 PSI)
7 MPa (1015 PSI)
8 MPa (1160 PSI)
Pull-out strength on concrete CSA A23.2-6B 7 days
28 days
1.25 MPa (181 PSI)
1.50 MPa (217 PSI)

Total volumetric shrinkage

 ASTM C-157   (Dry curing)

Coverage per bag of 22,7 kg of product   2.8 m² (30 ft²) pour une épaisseur de 6 mm (1/4”)
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Econo Plan
Eagle Econo Plan
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.

FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
PDFdownload PDF version