Eagle Finition Sanded Polymer Modified Cementitious Grout Français
Description
Eagle Finition is a modified polymer sanded Portland cement grout that only requires water for ceramic tile joints. This high performance grout is suitable for tiles applied vertically or horizontally, either inside or outside. This product surpasses ANSI A118.6. A wide selection of carefully chosen color can fill joints whose width varies between 3 mm (1/8") and 16 mm (5/8").
Surface Preparation
Ensure that tiles are firmly fixed and the adhesive has sufficiently dried before grouting. Remove all spacers from joints. Remove excess adhesive from joints, taking care to leave two thirds of joint depth free for grouting. Clean joint spaces to remove water, dust, dirt, debris or any other matters which may affect grout performance and consistency. Clean tile surface to remove any dust, dirt or contaminants that may affect grout integrity and color.
Application
Ambient, surface and product temperature must be above 10 º C (50 º F) and below 35 º C (95 º F) during application and for the first 24 hours. Place grout in joints with a rubber trowel. With a 45º angle and being diagonal to joint lines, fill, compact and screed grout in the joints, taking care not to leave any voids. Remove as much excess grout from the job surface by using the edge of the trowel rubber maintained at 90º and passing diagonally across the joints. Let the grout dry until there is no more transfer of product during a light finger pressure on joints. With a cellulosic sponge, use as little water as possible, place and smooth grout, passing diagonally across the joints while cleaning tile surface. Rinse sponge regularly in order to remove excess color and sand. It is necessary to twist up any excess water from the sponge to have a uniform and efflorescence free joint. Wait until next day before removing residual film left by with a clean dry white cloth. Outside, avoid working under an intense sun and protect from rain or liquids for 24 hours.
Mixing
In a clean container, pour 210 ml of fresh and clean water per kg of product, and add gradually Eagle Finition powder while mixing with a low speed drill and mixer. Stir for 2-3 minutes, scraping recipient walls and paddle to obtain a homogeneous and trowelable consistency.Let sit for 5 minutes, than remix without adding any more water or powder. Proceed to the application and finishing. Clean tools and hands with water while product is still fresh.
Curing
Eagle Finish takes about 20 to 30 minutes to dry before cleaning. Temperature and relative humidity may affect drying time. Protect surface against rain, sun and wind. If you use a polyethylene, this should be done without surface contact that could alter the finish. Wait about 2 to 3 hours before allowing light traffic.
Package
This product is available in 5 kg, 11.34 kg ang 22,7 bag.
Storage
Store in a cool, dry place. Shelflife is 12 months in original unopened containers.
Technical Data Table
CARACTERISTICS Eagle Finition
time required before finishing and sponge cleaning 20 to 30 minutes
Light circulation time required 2 to 3 hours
Final Cure 7 days
 

* Drying Time depend of surface porosity and temperature.

Restriction
Some ceramic tiles, agglomerated or natural stone can be stained, scratched or dulled by grouts containing pigments and sand. Consult tile manufacturer to know what type and color of grout to use. To make sure, test grout on a small sample to determine if a sanded grout and color is appropriate.
Warranty
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Finition Sanded
Eagle Finition Sanded
Ecologic
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.


FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
 
PDFdownload PDF version