Eagle Plan Wear Surface Self-Leveling Topping Compound Français
Description
EAGLE PLAN is a fast-curing, polymer modified, cementitious self-leveling mortar that allows smoothing and leveling interior wood and concrete floors rapidly with less work. This mortar can be used as a wear surface but also as an underlayment. The thickness could vary from 2 mm to 25 mm (1/8” to 1”). This compound allows smooth surfaces to install carpet, ceramic tiles, natural stone, hardwood, vinyl tiles and resilient floor covering. This self-leveling product can also be used over a low temperature radiant heating system installed on floors.
Surface Preparation
All surface shall be structurally sound, clean and free from traces of dust, oil, grease, wax, paint, curing agent, coatings and loose particles, acids, alkalis or any other material that can reduce adhesion. All concrete substrates shall be completely cured and at least 28 days old. It must be roughened for more adhesion and remove completely all traces of paint, coating, loosely bonded toppings. If concrete is too dry and porous, use of Eagle Prime Plus as primer is a good alternative to concrete water saturation. Otherwise, saturate concrete surface with clean water within few hours before repairs leaving no excess water and apply mortar when surface is dry again. Wood floors should be done with new exterior grade plywood used only in interior dry floors. Plywood should be supported by joists spaced every 40 cm (16”). The substrate consisting of two plywood sheets of 16mm (5/8”) thick each superposed cross-directionally. Allow a minimum of 3 mm (1/8”) spacing between them and screwed at intervals of 15 cm (6”) around the perimeter and 20 cm (8”) centrally. Maximum deflection should not exceed 1/360 of span. When using a self-leveling product over a radiant heating system, it is necessary to turn off 24 hours prior to installation and wait a week before turning it back on. Ambient surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during the installation and for the first 24 hours.
Mixing
In a clean container, pour exactly 4.77 litres of fresh clean water and gradually add 22.7 kg of Eagle Plan powder while mixing with a low-speed drill and a mixer. Blend for 2 to 3 minutes scraping recipient walls and paddle to obtain a homogeneous malleable and lump-free consistency. Wait 5 minutes and mix again for 1 minute. Apply immediately.
Curing
Protect application from any direct ventilation or heat radiation sources, such as direct sunlight during and after application for a minimum of 24 hours. These conditions could cause micro-cracking. Eagle Plan takes 2 to 3 hours to set, depending on consistency and ambient conditions. Curing time may vary according to temperature and humidity level. Wait 24 hours before light traffic.
Cleanning
Clean working tools and hands with water while product is still fresh.
Package
This product is available in 22.7 kg bag.
Storage
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container.
Technical Data Table
CARACTERISTICS CURE EAGLE PLAN (21% WATER)
Working time   30 minutes
Set time initial / final ASTM C-191   1 :00 hour / 2 :30 hours
Time allowed before installing floor covering or coating   16 to 24 hours depending on ºT and R.H.
Self-leveling capacity   20 minutes
Density ASTM C-185   2.02 kg/L
Compressive strength ASTM C-109 24 hours
7 days
28 days
21 MPa (3046 PSI)
28 MPa (4061 PSI)
38 MPa (5511 PSI)
Flexural strength ASTM C-348 24 hours
7 days
28 days
8.5 MPa (1233 PSI)
12.0 MPa (1740 PSI)
12.0 MPa (1740 PSI)
Pull-out strength on concrete CSA A23.2-6B 7 days
28 days
2.42 MPa (351 PSI)
2.47 MPa (351 PSI)
Total linear shrinkage ASTM C-157 (dry curing)   -0.07%
Coverage per bags of 22,7 kg of product   2.23 m² (24 ft²) for 6 mm (1/4”) thickness
 

* Drying Time depend of surface porosity and temperature.

Warranty
The customer shall verify of the suitability of this product for the intended purpose. Applicator's skill, weather and surface conditions being beyond manufacturer's control, we limit our liability to replacement of defective material only in sealed container, within 1 year of proof of purchase. FOB plant.

Eagle Plan
Eagle Plan
Ecologic
Avertissement Simdut Simdut

CORROSIVE: This product contains a cementitious blend and may cause eyes, skin and respiratory system irritation. When using this product: Wear safety glasses, gloves and a NIOSH approved anti-dust mask. Keep out of reach of children.


FIRST AID TREATEMENT: Skin contact: Wash with soap and water. Eye contact: Flush eyes immediately and abundantly with water for 15 minutes keeping eyelids opened. Consult a physician immediately. Ingestion: DO NOT INDUCE VOMITING. Give water if conscious. Keep victim warm and call immediately a physician.
 
PDFdownload PDF version